It's smack in the middle of both April and my Kids Craft Week. Today I did a project that I've always wanted to do... making a Kaleidoscope.
It was a really fun and quick project- I've never made one before but I was able to work out the details and have the actual kaleidoscope made all before work this morning. This project would be suitable for older kids (with adult supervision). If you wanted to make this with a younger child they could choose the beads that go inside and decorate the outside tube. While I was making this it seemed like it would be a fun thing to do at a kids party.
Here's What You'll Need:
- One mailing tube with plastic caps for the ends (it should be slightly smaller or about the same size as a TP tube).
- One toilet paper tube
- Three mirrors or an already assembled prism toy that is smaller than your tp tube.
- Clear Duct Tape
- A handful of beads, bits, and cool things.
- One small clear container- the kind that little beads and grommets from the craft store are packaged in. (You can also buy these small containers. I found mine at a dollar store)
- One sheet of white cardstock
- One sheet of decorative paper or stickers, and markers.
- A scrap of vellum (big enough to cut out a circle the size of your mailing tube).
- Optional- Glue that can be used on plastic.
- You'll also need a craft knife, scissors, paper glue, and a pencil
Here We Go:
To start you'll need a prism-
I didn't make mine I purchased it ( they sell them as toys) and took the decorative paper wrapper off (mostly since I was taking pictures of it) but you could make your own easily. You would need three mirrors about 1/2 inch wide x 3 inches long, taped together to make a triangle.
Once you have the prism you need to cut your tp tube up the side and roll it into a smaller sized tube so that the prism will fit snugly inside. Then tape it so it stays that size. (I taped the edge with regular duct tape but later used the clear tape- either is fine.)
Then I rolled the tp tube in cardstock until it was thick enough to fit snugly into the mailing tube without jiggling around.
Once I had this done I traced the bottom of the clear container on the vellum and cut out a circle.
Then I filled the container with beads, bits of paper, and even some scraps of soda bottle plastic from Monday's project.
I noticed that the mailing tube seemed long- I lined up the tp tube, the bead container, and the plastic cap to estimate the length I needed. I made a pencil mark all the way around and used a craft knife to cut the mailing tube down to about half the length.
I put the tp tube into the mailing tube and stuck the plastic container on the other end. It was at this point that I realized that the lid on the container could easily come off and spill beads everywhere (ask me how I found that out, it may have had something to do with beads flying all over the studio... maybe). So I took the container back out of the tube (picked up all the beads I could find) and decided to tape the edges closed (you could use plastic glue here too).
Then put it back into the end of the mailing tube and taped the vellum onto the top (you could also glue this- it would look neater- but the tape worked fine).
Last- but a very important part of construction for the finished kaleidoscope is to make the eyepiece. I used one of the plastic caps that came with the mailing tube.
With a craft knife I made a hole, then used the end of a paper craft tool to smooth it down a bit.
I put the cap into the other end of the tube. (Now I had a tube with the vellum then the plastic container on one end- the TP/prism tube in the middle and the eye piece at the other end.)
To finish I covered the outside with decorative paper. You could also cover it with white paper and use markers, stickers, and paper punches to decorate.
It works great, and was so much fun that I kind of want to make a few more! It's also got me thinking how neat it would be to make some holiday specific kaleidoscopes.
And If you missed it, here's Tuesdays project: tye-dye coffee filter spring critters